Pipeng Toolbox : Beam Added Mass Calculators Blank User
Short Cuts
GO
Main ±
Beams ±
References ±
Fluid Flow ±
Fluid Properties ±
Maths ±
Materials ±
Pipelines ±
Soils ±
Subsea ±
Demo

Beam Cross Section Added Mass

Calculate beam cross section added mass coefficient and added mass from gap height for circular pipes and beams.

Added mass is included in the unit mass for submerged beams to account for the fluid which is displaced by the beam. The added mass coefficient can be calculated in accordance with DNVGL RP F105. The equation is suitable for undamped vibration of circular beams in still fluid. For circular pipes the diameter should be used as the characteristic length. For other profile shapes the width can be used as the characteristic length. The method may not be valid for other profile shapes (engineering judgement is required). Refer to the help pages for more details.

Reference : Roark's Formulas For Stress And Strain, Warren C Young, McGraw Hill

Change Module :

[FREE] tools are free in basic mode with no login (no plots, tables, goal seek etc). Login or Open a free account to use the tools in plus mode (with plots, tables, goal seek etc).
[PLUS] tools are free in basic CHECK mode with Login or Open a free account (CHECK values no plots, tables, goal seek etc). Buy a Subscription to use the tools in plus mode (with plots, tables, goal seek etc).
Try plus mode using the Plus Mode Demo tools with no login.   Help Using The Pipeng Toolbox (opens in the popup workbook)

Links : ±
CALCULATOR : Beam Cross Section Added Mass Coefficient (Circular Beam) [FREE]   ±

Calculate beam added mass coefficient and added mass from gap height for a circular beam.

Added mass is included in the unit mass for submerged beams to account for the fluid which is displaced by the beam. The added mass coefficient is calculated in accordance with DNVGL RP F105. The equation is suitable for undamped vibration of circular beams in still fluid. Refer to the help pages for more details.

Reference : DNVGL RP F105 Free Spanning Pipelines (Download From DNVGL website)

Tool Input

  • schdtype : Schedule Type
  • diamtype : Diameter Type
    • ODu : User Defined Outside Diameter
    • IDu : User Defined Inside Diameter
  • wtntype : Wall Thickness Type
    • tnu : User Defined Wall Thickness
  • cmtype : Added Mass Coefficient Type
    • Cmu : User Defined Added Mass Coefficient
  • mb : Beam Mass Per Unit Length
  • ρe : External Fluid Density
  • G : Gap Height

Tool Output

  • Cm : Added Mass Coefficient
  • G/OD : Gap Over Diameter Ratio
  • OD : Outside Diameter
  • m : Total Mass Per Unit Length
  • ma : Added Mass Per Unit Length
CALCULATOR : Beam Cross Section Added Mass Coefficient (General Beam) [FREE]   ±

Calculate beam added mass coefficient and added mass from gap height and characteristic length for a general beam.

Added mass is included in the unit mass for submerged beams to account for the fluid which is displaced by the beam. The added mass coefficient is calculated in accordance with DNVGL RP F105. The equation is suitable for undamped vibration of circular pipes in still fluid. For circular pipes the diameter should be used as the characteristic length. For other profile shapes the width can be used as the characteristic length. The method may not be valid for other profile shapes (engineering judgement is required). Refer to the help pages for more details.

Reference : DNVGL RP F105 Free Spanning Pipelines (Download From DNVGL website)

Tool Input

  • cmtype : Added Mass Coefficient Type
    • Cmu : User Defined Added Mass Coefficient
  • mb : Beam Mass Per Unit Length
  • ρe : External Fluid Density
  • W : Beam Characteristic Length
  • G : Gap Height
  • AX : Beam Cross Section Area

Tool Output

  • Cm : Added Mass Coefficient
  • G/W : Gap Over Characteristic Length Ratio
  • m : Total Mass Per Unit Length
  • ma : Added Mass Per Unit Length
CALCULATOR : Beam Cross Section Line Pipe Schedule [FREE]   ±

Calculate line pipe schedule outside diameter inside diameter and wall thickness.

Select the pipe schedule (NPS or ISO etc), pipe diameter and wall thickness, or use the user defined option. Use the Result Table option to display the pipe schedule for the selected diameter.

Tool Input

  • schdtype : Line Pipe Schedule Type
  • diamtype : Line Pipe Diameter Type
    • ODu : User Defined Outside Diameter
    • IDu : User Defined Inside Diameter
  • wtntype : Wall Thickness Type
    • tnu : User Defined Wall Thickness

Tool Output

  • ID : Nominal Inside Diameter
  • OD : Nominal Outside Diameter
  • OD/tn : Diameter Over Wall Thickness Ratio
  • tn : Nominal Wall Thickness
pipeng.com 2026 (697 μs : 5 ms : 0.730 MB) Pengu CMS ©