Pipeng Toolbox : DNV-OS-F101 Pipeline Calculators Login
Short Cuts
GO
Main ±
Beams ±
References ±
Fluid Flow ±
Fluid Properties ±
Maths ±
Materials ±
Pipelines ±
Soils ±
Subsea ±
Data ±
Units ±
Help ±
Demo

DNV OS F101 Submarine Pipeline

DNV OS-F101 Submarine Pipeline Systems has been replaced by DNVGL-ST-F101.

Reference : DNVGL-ST-F101 : Submarine Pipeline Systems (Download from the DNVGL website)

Change Module :

[FREE] tools are free in basic mode with no login (no plots, tables, goal seek etc). Login or Open a free account to use the tools in plus mode (with plots, tables, goal seek etc).
[PLUS] tools are free in basic CHECK mode with Login or Open a free account (CHECK values no plots, tables, goal seek etc). Buy a Subscription to use the tools in plus mode (with plots, tables, goal seek etc).
Try plus mode using the Plus Mode Demo tools with no login.   Help Using The Pipeng Toolbox (opens in the popup workbook)

Links : ±
CALCULATOR : DNVGL ST F101 Section 5.3.3 Subsea Pipeline Derated Yield Stress And Tensile Stress From Temperature [FREE]   ±

Calculate subsea pipeline temperature derating stress from temperature (DNVGL-ST-F101 section 5.3.3 Figure 5-2).

The derating stress is valid for temperatures up to 200 degrees C. For temperatures above 200 C material tests should be performed. For low temperature pipelines fracture toughness should also be considered.

Use the Result Table option to display a table of derated yield stress versus material type at the design temperature. Use the Result Plot option to display a plot of derated yield stress versus temperature for duplex stainless 22Cr 25Cr, and carbon manganese steel 13Cr curves.

Tool Input

  • syutype : Stress Table Type
  • mattype : Material Strength Type
    • SMYSu : User Defined Specified Minimum Yield Stress
    • SMTSu : User Defined Specified Minimum Tensile Stress
  • syttype : Temperature Derating Type
    • fytu : User Defined Yield Stress Temperature Derating
    • futu : User Defined Ultimate Stress Temperature Derating
  • autype : Material Strength Factor Type
  • Td : Design Temperature

Tool Output

  • αu : Material Strength Factor
  • SMTS : Specified Minimum Tensile Stress
  • SMYS : Specified Minimum Yield Stress
  • fcb : Burst Stress
  • fu : Tensile Stress
  • fut : Temperature Derating Tensile Stress
  • fy : Yield Stress
  • fyt : Temperature Derating Yield Stress
CALCULATOR : DNVGL ST F101 Subsea Pipeline Diameter And Wall Thickness Schedule [FREE]   ±

Calculate DNVGL-ST-F101 subsea pipeline diameter and pressure design wall thickness from pipe schedule.

The pressure design thickness equals the nominal wall thickness minus the corrosion allowance and fabrication allowance. The minimum wall thickness equals the nominal wall thickness minus the fabrication allowance. The corrosion allowance includes mechanical allowances such as threads and damage etc. Use the Result Table option display a table of pressure design wall thickness versus wall thickness for the selected diameter schedule.

Tool Input

  • schdtype : Schedule Type
  • diamtype : Diameter Type
    • ODu : User Defined Outside Diameter
    • IDu : User Defined Inside Diameter
  • wtntype : Wall Thickness Type
    • tnu : User Defined Wall Thickness
  • ttoltype : Wall Thickness Fabrication Tolerance Type
    • txu : User Defined Negative Wall Thickness Fraction
    • tfu : User Defined Negative Wall Thickness Allowance
  • c : Wall Thickness Corrosion Allowance

Tool Output

  • ID : Nominal Inside Diameter
  • OD : Nominal Outside Diameter
  • OD/tn : Diameter Over Wall Thickness Ratio
  • tf : Wall Thickness Fabrication Allowance
  • tm : Minimum Wall Thickness
  • tn : Nominal Wall Thickness
  • tp : Pressure Design Wall Thickness
  • tx : Wall Thickness Fabrication Fraction
CALCULATOR : DNVGL ST F101 Subsea Pipeline Mass Per Length And Total Mass Schedule [FREE]   ±

Calculate DNVGL-ST-F101 subsea pipeline unit mass and total mass from pipe schedule or user defined pipe diameter and wall thickness.

Select the pipe schedule (NPS or ISO), pipe diameter and wall thickness, or use the user defined option. Use the Result Table option display a table of pipe mass versus wall thickness for the selected diameter schedule.

Tool Input

  • schdtype : Schedule Type
  • diamtype : Diameter Type
    • ODu : User Defined Outside Diameter
    • IDu : User Defined Inside Diameter
  • wtntype : Wall Thickness Type
    • tnu : User Defined Wall Thickness
  • modptype : Material Property Type
    • ρpu : User Defined Pipe Density
  • L : Pipe Length

Tool Output

  • ρp : Pipe Density
  • ID : Nominal Inside Diameter
  • M : Pipe Total Mass
  • OD : Nominal Outside Diameter
  • OD/tn : Diameter Over Wall Thickness Ratio
  • m : Pipe Mass Per Length
  • tn : Nominal Wall Thickness
CALCULATOR : DNVGL ST F101 Subsea Pipeline Weight Including Contents And Buoyancy (Multi Layer Pipe) [FREE]   ±

Calculate DNVGL-ST-F101 subsea pipeline weight including contents and buoyancy for multi layer pipelines.

Calculate weight per length for dry empty, dry full, wet empty and wet full pipelines. Change the number of layers on the setup page. The external fluid density is not required for dry pipelines.

Tool Input

  • schdtype : Line Pipe Schedule Type
  • diamtype : Line Pipe Diameter Type
    • ODu : User Defined Outside Diameter
    • IDu : User Defined Inside Diameter
  • wtntype : Line Pipe Wall Thickness Type
    • tnu : User Defined Wall Thickness
  • wltype : Pipe Weight Type
  • WTi : Pipe Liner Wall Thickness
  • ρi : Pipe And Liner Density
  • WTo : Pipe Coating Wall Thickness
  • ρo : Pipe Coating Density
  • ρf : Contents Fluid Density
  • ρb : Displaced Fluid Density

Tool Output

  • IID : Pipe Inner Diameter Including Liners
  • OD : Line Pipe Nominal Diameter
  • OOD : Pipe Outer Diameter Including Coatings
  • SG : Pipe Specific Gravity Relative To Displaced Fluid
  • mb : Displaced Fluid Mass Per Length
  • mc : Contents Fluid Mass Per Length
  • mi : Inner Layers Total Unit Mass
  • mo : Outer Layers Total Unit Mass
  • mp : Pipe Mass Per Length Including Liner And Coating
  • tn : Line Pipe Nominal Wall Thickness
  • w : Pipe Total Weight Per Length Including Contents and Buoyancy
pipeng.com 2025 (706 μs : 5 ms : 0.751 MB) Pengu CMS ©