Calculate the erosion rate for choke gallery (DNVGL-RP-O501 section 4.12).
Tool Input
- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Pipe Outside Diameter
- IDu : User Defined Pipe Inside Diameter
- wtntype : Pipe Wall Thickness Type
- tnu : User Defined Pipe Wall Thickness
- mvtype : Fluid Density Type
- GORu : User Defined Gas Oil Ratio
- WCu : User Defined Water Cut
- ρu : User Defined Fluid Density
- voltype : Fluid Volume Flowrate Type
- Qou : User Defined Oil Volume Flow Rate
- Qlu : User Defined Liquid Volume Flow Rate
- Ngu : User Defined Gas Mole Flow Rate
- Qfu : User Defined Total Fluid Volume Flow Rate
- Mfu : User Defined Total Fluid Mass Flow Rate
- Vfu : User Defined Pipe Fluid Velocity
- Vfu : User Defined Pipe Fluid Velocity
- visctype : Viscosity Type (Must Be User Defined For User Defined Density)
- μu : User Defined Dynamic Viscosity
- νu : User Defined Kinematic Viscosity
- pipetype : Pipe Material Type
- ρpu : User Defined Pipe Density
- Ku : User Defined Pipe K Factor
- nu : User Defined Pipe n Factor
- sandtype : Sand Material Type
- ρsu : User Defined Particle Density
- Su : User Defined Sand K Correction Factor
- conctype : Sand Concentration Type
- Qsu : User Defined Sand Volume Flow Rate
- Msu : User Defined Sand Mass Flow Rate
- ppmVu : User Defined Sand ppm Volume
- ppmMu : User Defined Sand ppm Mass
- Msyu : User Defined Sand Annual Mass Load
- lfactype : Erosion Loss Factor Type
- Lu : User Defined Erosion Loss Factor
- gftype : Geometry Factor Type
- GFu : User Defined GF Geometry Factor
- ρo : Oil Density
- ρw : Water Density
- P : Fluid Absolute Pressure
- T : Fluid Absolute Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
- μo : Oil Dynamic Viscosity
- μw : Water Dynamic Viscosity
- μg : Gas Dynamic Viscosity
- Ds : Average Sand Diameter
- R : Choke Gallery Radius
- H : Choke Gallery Height
- D : Choke Gallery Width
Tool Output
- α : Characteristic Impact Angle
- β : Sand Density Over Fluid Density Ratio
- γ : Sand Density Over Pipe Diameter Ratio
- γc : Critical Sand Density Over Pipe Diameter Ratio
- μ : Fluid Dynamic Viscosity
- ν : Fluid Kinematic Viscosity
- ρf : Average Fluid Density
- ρg : Gas Density
- ρl : Liquid Density
- ρp : Pipe Density
- ρs : Sand Density
- A : Ratio A
- Ag : Choke Gallery Effective Area
- At : Area Exposed To Erosion
- C1 : Particle Correction Factor
- F(α) : Impact Angle Factor
- G : Partcle Size Correction Factor
- GF : Geometry Factor
- GOR : Gas Oil Ratio
- ID : Pipe Inside Diameter
- K : Pipe K Factor
- L : Corrosion Loss Factor
- Mf : Total Fluid Mass Flow Rate
- Ms : Sand Mass Flow Rate
- Qf : Total Fluid Volume Flow Rate
- Qs : Sand Volume Flow Rate
- ROD : Choke Gallery Radius Over Width Ratio
- Re : Choke Gallery Reynolds Number
- S : Sand K Correction Factor
- Vc : Choke Gallery Fluid Velocity
- Vp : Pipe Fluid Velocity
- WC : Water Cut
- Xvg : Gas Volume Fraction
- Xvl : Liquid Volume Fraction
- Xvo : Oil Volume Fraction
- Xvw : Water Volume Fraction
- n : Pipe n exponent
- ppmM : Sand Concentration Parts Per Million Mass
- ppmV : Sand Concentration Parts Per Million Volume
- vg : Gas Mole Volume