Calculate fluid dose rate (volume rate or mass rate) and dosed fluid density.
The fluid density, volume fraction and mass fraction includes the dosing fluid (combined undosed fluid and dose chemical).
| Links : ± |
CALCULATOR : Gas Density And Compressibility Factor [FREE] ±
Calculate single phase gas compressibility factor and density from gas temperature and pressure for selected gases. The gas compressibility factor is calculated from the critical point temperature, critical point temperature, and the accentric factor using either the Peng Robinson, Soave, Redlich Kwong or Van Der Waals equations of state (EOS). The compressibility factor calculation is valid for gas phase only. Use the Result Plot option to plot compressibility factor versus pressure and temperature, compressibility factor versus pressure and equation of state type, or compressibility factor versus temperature and equation of state type. Tool Input- fluidtype : Fluid Type
- SGu : User Defined Gas Specific Gravity
- ωu : User Defined Acentric Factor
- Pcu : User Defined Critical Pressure
- Tcu : User Defined Critical Temperature
- eostype : Equation Of State
- Zu : User Defined Compressibility Factor
- P : Fluid Pressure
- T : Fluid Temperature
Tool Output- ρ : Fluid Density
- ω : Accentric Factor
- Pc : Critical Point Pressure
- Pr : Reduced Pressure
- SG : Gas Specific Gravity Relative To Air
- Tc : Critical Point Temperature
- Tr : Reduced Temperature
- Vm : Molar Volume
- Z : Compressibility Factor
- cvg : Convergence Check
- mw : Fluid Molar Mass
|
CALCULATOR : Pipe Inside Diameter And Cross Section Area [FREE] ±
Calculate pipe inside diameter and inside cross section area from pipe diameter and wall thickness. Use the Result Table option to display a table of the inside diameter and cross section area versus either outside diameter or wall thickness. Tool Input- schdtype : Schedule Type
- diamtype : Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
Tool Output- AX : Pipe Inside Cross Section Area
- ID : Nominal Inside Diameter
- OD : Nominal Outside Diameter
- OD/tn : Diameter Over Wall Thickness Ratio
- tn : Nominal Wall Thickness
|
CALCULATOR : Single Phase Liquid Chemical Dose Rate And Density [FREE] ±
Calculate the liquid dose rate in a single phase liquid. The dose rate can be calculated from the dose volume fraction, the dose mass fraction, the dose volume ratio, or the dose mass ratio. The average fluid density includes the dose chemical. Tool Input- dosetype : Dosage Type
- Xvu : User Defined Dose Volume Fraction
- Xmu : User Defined Dose Mass Fraction
- Rvu : User Defined 200
- Rmu : User Defined 250
- ρl : Liquid Density
- ρd : Dose Chemical Density
Tool Output- ρf : Fluid Average Density
- Rm : Dose Mass Ratio
- Rv : Dose Volume Ratio
- Xm : Dose Mass Fraction
- Xv : Dose Volume Fraction
|
CALCULATOR : Single Phase Liquid Chemical Dose Rate Density And Volume [FREE] ±
Calculate the pipeline liquid dose rate and volume in a single phase liquid. The dose rate can be calculated from the dose volume fraction, the dose mass fraction, the dose volume ratio, or the dose mass ratio. The average fluid density includes the dose chemical. The dose volume can be calculated for the liquid phase, the total fluid (including dose chemical), or the pipeline length. Tool Input- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
- dosetype : Dosage Type
- Xvu : User Defined Dose Volume Fraction
- Xmu : User Defined Dose Mass Fraction
- Rvu : User Defined 200
- Rmu : User Defined 250
- voltype : Fluid Volume Type
- Vlu : User Defined Liquid Volume
- Mlu : User Defined Liquid Mass
- Vfu : User Defined Total Fluid Volume
- Mfu : User Defined Total Fluid Mass
- Lu : User Defined Pipeline Length
- ρl : Liquid Density
- ρd : Dose Chemical Density
Tool Output- ρf : Fluid Average Density
- ID : Inside Diameter
- L : Pipe Length
- Md : Dose Mass
- Mf : Total Fluid Mass
- Ml : Liquid Mass
- Rm : Dose Mass Ratio
- Rv : Dose Volume Ratio
- Vd : Dose Volume
- Vf : Total Fluid Volume
- Vl : Liquid Volume
- Xm : Dose Mass Fraction
- Xv : Dose Volume Fraction
|
CALCULATOR : Single Phase Liquid Chemical Dose Rate Density And Flow Rate [FREE] ±
Calculate the pipeline liquid dose rate and volume flowrate in a single phase liquid. The dose rate can be calculated from the dose volume fraction, the dose mass fraction, the dose volume ratio, or the dose mass ratio. The average fluid density includes the dose chemical. The dose volume flowrate can be calculated for the liquid phase or the total fluid (including dose chemical). Tool Input- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
- dosetype : Dosage Type
- Xvu : User Defined Dose Volume Fraction
- Xmu : User Defined Dose Mass Fraction
- Rvu : User Defined 200
- Rmu : User Defined 250
- voltype : Fluid Volume Flow Rate Type
- Qlu : User Defined Liquid Volume Flow Rate
- Mlu : User Defined Liquid Mass Flow Rate
- Vlu : User Defined Liquid Superficial Velocity
- Qfu : User Defined Total Volume Flow Rate
- Mfu : User Defined Total Mass Flow Rate
- Vfu : User Defined Total Fluid Velocity
- ρl : Liquid Density
- ρd : Dose Chemical Density
Tool Output- ρf : Fluid Average Density
- ID : Inside Diameter
- Md : Dose Mass Flow Rate
- Mf : Total Fluid Mass Flow Rate
- Ml : Liquid Mass Flow Rate
- Qd : Dose Volume Flow Rate
- Qf : Total Fluid Volume Flow Rate
- Ql : Liquid Volume Flow Rate
- Rm : Dose Mass Ratio
- Rv : Dose Volume Ratio
- Vd : Superficial Dose Chemical Velocity
- Vf : Total Fluid Velocity
- Vl : Superficial Liquid Velocity
- Xm : Dose Mass Fraction
- Xv : Dose Volume Fraction
|
CALCULATOR : Single Phase Gas Chemical Dose Rate And Density [FREE] ±
Calculate the liquid dose rate in a single phase gas. The dose rate can be calculated from dose volume fraction, dose mass fraction or dose gas ratio. The average fluid density includes the dose chemical. Tool Input- dosetype : Dose Rate Type
- Xvu : User Defined Dose Volume Fraction
- Xmu : User Defined Dose Mass Fraction
- Rvu : User Defined Dose Volume Over Gas Moles Ratio
- Rmu : User Defined Dose Mass Over Gas Moles Ratio
- ρd : Dose Chemical Density
- P : Fluid Pressure
- T : Fluid Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
Tool Output- ρf : Fluid Average Density
- ρg : Gas Density (At T P)
- Rm : Dose Mass Over Gas Moles Ratio
- Rv : Dose Volume Over Gas Moles Ratio
- Xm : Dose Mass Fraction
- Xv : Dose Volume Fraction
- vg : Gas Mole Volume (At T P)
|
CALCULATOR : Single Phase Gas Chemical Dose Rate Density And Volume [FREE] ±
Calculate the pipeline liquid dose rate and volume in a single phase gas. The dose rate can be calculated from dose volume fraction, dose mass fraction or dose gas ratio. The average fluid density includes the dose chemical. The dose volume can be calculated for the gas phase, the total fluid (including dose chemical), or the pipeline length. Tool Input- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
- dosetype : Dose Rate Type
- Xvu : User Defined Dose Volume Fraction
- Xmu : User Defined Dose Mass Fraction
- Rvu : User Defined Dose Volume Over Gas Moles Ratio
- Rmu : User Defined Dose Mass Over Gas Moles Ratio
- voltype : Fluid Volume Type
- Vgu : User Defined Gas Volume
- Mgu : User Defined Gas Mass
- Ngu : User Defined Gas Moles
- Vfu : User Defined Total Fluid Volume
- Mfu : User Defined Total Fluid Mass
- Lu : User Defined Pipeline Length
- ρd : Dose Chemical Density
- P : Fluid Pressure
- T : Fluid Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
Tool Output- ρf : Fluid Average Density
- ρg : Gas Density (At T P)
- ID : Inside Diameter
- L : Pipe Length
- Md : Dose Mass
- Mf : Total Fluid Mass
- Mg : Gas Mass
- Ng : Gas Moles
- Rm : Dose Mass Over Gas Moles Ratio
- Rv : Dose Volume Over Gas Moles Ratio
- Vd : Dose Volume
- Vf : Total Fluid Volume
- Vg : Gas Volume
- Xm : Dose Mass Fraction
- Xv : Dose Volume Fraction
- vg : Gas Mole Volume (At T P)
|
CALCULATOR : Single Phase Gas Chemical Dose Rate Density And Flow Rate [PLUS] ±
Calculate the pipeline liquid dose rate and volume flowrate in a single phase gas. The dose rate can be calculated from dose volume fraction, dose mass fraction or dose gas ratio. The average fluid density includes the dose chemical. The dose volume flowrate can be calculated for the gas phase or the total fluid (including dose chemical). Tool Input- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
- dosetype : Dose Rate Type
- Xvu : User Defined Dose Volume Fraction
- Xmu : User Defined Dose Mass Fraction
- Rvu : User Defined Dose Volume Over Gas Moles Ratio
- Rmu : User Defined Dose Mass Over Gas Moles Ratio
- voltype : Fluid Volume Type
- Qgu : User Defined Gas Volume Flow Rate
- Mgu : User Defined Gas Mass Flow Rate
- Vgu : User Defined Gas Superficial Velocity
- Ngu : User Defined Gas Mole Flow Rate
- Qfu : User Defined Total Volume Flow Rate
- Mfu : User Defined Total Mass Flow Rate
- Vlu : User Defined Total Fluid Velocity
- ρd : Dose Chemical Density
- P : Fluid Pressure
- T : Fluid Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
Tool Output- ρf : Fluid Average Density
- ρg : Gas Density (At T P)
- ID : Inside Diameter
- Md : Dose Mass Flowrate
- Mf : Total Fluid Mass Flowrate
- Mg : Gas Mass Flowrate
- Ng : Gas Mole Flowrate
- Qd : Dose Volume Flowrate
- Qf : Total Fluid Volume Flowrate
- Qg : Gas Volume Flowrate
- Rm : Dose Mass Over Gas Moles Ratio
- Rv : Dose Volume Over Gas Moles Ratio
- Vd : Superficial Dose Chemical Velocity
- Vf : Total Fluid Velocity
- Vg : Superficial Gas Velocity
- Xm : Dose Mass Fraction
- Xv : Dose Volume Fraction
- vg : Gas Mole Volume (At T P)
|