Calculate three phase gas oil water (black oil) heat capacity.
Black oil is a three phase mixture of oil, water and gas. Water cut is measured relative to the total liquid volume (gas volume is ignored). Gas oil ratio (GOR) is measured relative to the oil volume at standard conditions (water volume is ignored). Gas oil ratio (GOR) is the ratio of gas moles over liquid volume. Gas moles are commonly measured by standard cubic feet (scf), and stand cubic meters (scm). Gas oil ratio is often measured as gas standard volume (scf or scm) per oil volume (barrels, gallons, cubic feet or cubic meters).
| Links : ± |
CALCULATOR : Three Phase Black Oil Heat Capacity [FREE] ±
Calculate three phase black oil heat capacity from oil phase, water phase and gas phase heat capacity. Heat capacity can be calculated/entered for either constant pressure Cp, or constant volume Cv. Black oil is a three phase mixture of oil, water and gas. Water cut is measured relative to the total liquid volume (gas volume is ignored). Gas oil ratio (GOR) is measured relative to the oil volume at standard conditions (water volume is ignored). Tool Input- mvtype : Fluid Density Type
- GORu : User Defined Gas Oil Ratio
- WCu : User Defined Water Cut
- ρu : User Defined Fluid Density
- hcaptype : Fluid Heat Capacity Type
- Hu : User Defined Heat Capacity
- Ho : Oil Heat Capacity
- Hw : Water Heat Capacity
- Hg : Gas Heat Capacity
- ρo : Oil Density
- ρw : Water Density
- P : Fluid Pressure
- T : Fluid Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
Tool Output- ρf : Average Fluid Density
- ρg : Gas Density
- ρl : Liquid Density
- GOR : Gas Oil Ratio
- H : Fluid Heat Capacity
- WC : Water Cut
- Xmg : Gas Mass Fraction
- Xml : Liquid Mass Fraction
- Xmo : Oil Mass Fraction
- Xmw : Water Mass Fraction
- Xvg : Gas Volume Fraction
- Xvl : Liquid Volume Fraction
- Xvo : Oil Volume Fraction
- Xvw : Water Volume Fraction
- vg : Gas Mole Volume (At T P)
|
CALCULATOR : Three Phase Black Oil Pipeline Fluid Heat Capacity And Volume [PLUS] ±
Calculate three phase black oil heat capacity and pipeline volume from oil phase, water phase and gas phase heat capacity. Heat capacity can be calculated/entered for either constant pressure Cp, or constant volume Cv. Black oil is a three phase mixture of oil, water and gas. Water cut is measured relative to the total liquid volume (gas volume is ignored). Gas oil ratio (GOR) is measured relative to the oil volume at standard conditions (water volume is ignored). Tool Input- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
- mvtype : Fluid Density Type
- GORu : User Defined Gas Oil Ratio
- WCu : User Defined Water Cut
- ρu : User Defined Fluid Density
- voltype : Fluid Volume Type
- Vou : User Defined Oil Volume
- Vlu : User Defined Liquid Volume
- Ngu : User Defined Gas Moles
- Vfu : User Defined Total Fluid Volume
- Mfu : User Defined Total Fluid Mass
- Lu : User Defined Pipeline Length
- hcaptype : Fluid Heat Capacity Type
- Hu : User Defined Heat Capacity
- Ho : Oil Heat Capacity
- Hw : Water Heat Capacity
- Hg : Gas Heat Capacity
- ρo : Oil Density
- ρw : Water Density
- P : Fluid Pressure
- T : Fluid Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
Tool Output- ρf : Average Fluid Density
- ρg : Gas Density
- ρl : Liquid Density
- GOR : Gas Oil Ratio
- H : Fluid Heat Capacity
- ID : Inside Diameter
- L : Pipe Length
- Mf : Total Fluid Mass
- Mg : Gas Mass
- Ml : Liquid Mass
- Mo : Oil Mass
- Mw : Water Mass
- Ng : Gas Moles
- OD : Outside Diameter
- Vf : Total Fluid Volume
- Vg : Gas Volume
- Vl : Liquid Volume
- Vo : Oil Volume
- Vw : Water Volume
- WC : Water Cut
- Xmg : Gas Mass Fraction
- Xml : Liquid Mass Fraction
- Xmo : Oil Mass Fraction
- Xmw : Water Mass Fraction
- Xvg : Gas Volume Fraction
- Xvl : Liquid Volume Fraction
- Xvo : Oil Volume Fraction
- Xvw : Water Volume Fraction
- tn : Nominal Wall Thickness
- vg : Gas Mole Volume (At T P)
|
CALCULATOR : Three Phase Black Oil Pipeline Fluid Heat Capacity And Flow Rate [PLUS] ±
Calculate three phase black oil heat capacity amd pipeline flow rate from oil phase, water phase and gas phase heat capacity. Heat capacity can be calculated/entered for either constant pressure Cp, or constant volume Cv. Black oil is a three phase mixture of oil, water and gas. Water cut is measured relative to the total liquid volume (gas volume is ignored). Gas oil ratio (GOR) is measured relative to the oil volume at standard conditions (water volume is ignored). Tool Input- schdtype : Pipe Schedule Type
- diamtype : Pipe Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
- mvtype : Fluid Density Type
- GORu : User Defined Gas Oil Ratio
- WCu : User Defined Water Cut
- ρu : User Defined Fluid Density
- voltype : Fluid Volume Type
- Qou : User Defined Oil Volume Flow Rate
- Qlu : User Defined Liquid Volume Flow Rate
- Ngu : User Defined Gas Mole Flow Rate
- Qfu : User Defined Total Fluid Volume Flow Rate
- Mfu : User Defined Total Fluid Mass Flow Rate
- Vfu : User Defined Fluid Velocity
- hcaptype : Fluid Heat Capacity Type
- Hu : User Defined Heat Capacity
- Ho : Oil Heat Capacity
- Hw : Water Heat Capacity
- Hg : Gas Heat Capacity
- ρo : Oil Density
- ρw : Water Density
- P : Fluid Pressure
- T : Fluid Temperature
- Z : Gas Compressibility Factor
- SG : Gas Specific Gravity
Tool Output- ρf : Average Fluid Density
- ρg : Gas Density
- ρl : Liquid Density
- GOR : Gas Oil Ratio
- H : Fluid Heat Capacity
- ID : Inside Diameter
- Mf : Total Fluid Mass Flowrate
- Mg : Gas Mass Flowrate
- Ml : Liquid Mass Flowrate
- Mo : Oil Mass Flowrate
- Mw : Water Mass Flowrate
- Ng : Gas Mole Flowrate
- OD : Outside Diameter
- Qf : Total Fluid Volume Flowrate
- Qg : Gas Volume Flowrate
- Ql : Liquid Volume Flowrate
- Qo : Oil Volume Flowrate
- Qw : Water Volume Flowrate
- Vf : Average Fluid Velocity
- Vg : Gas Superficial Velocity
- Vl : Liquid Superficial Velocity
- Vo : Oil Superficial Velocity
- Vw : Water Superficial Velocity
- WC : Water Cut
- Xmg : Gas Mass Fraction
- Xml : Liquid Mass Fraction
- Xmo : Oil Mass Fraction
- Xmw : Water Mass Fraction
- Xvg : Gas Volume Fraction
- Xvl : Liquid Volume Fraction
- Xvo : Oil Volume Fraction
- Xvw : Water Volume Fraction
- tn : Nominal Wall Thickness
- vg : Gas Mole Volume (At T P)
|
CALCULATOR : Gas Density And Compressibility Factor [FREE] ±
Calculate single phase gas compressibility factor and density from gas temperature and pressure for selected gases. The gas compressibility factor is calculated from the critical point temperature, critical point temperature, and the accentric factor using either the Peng Robinson, Soave, Redlich Kwong or Van Der Waals equations of state (EOS). The compressibility factor calculation is valid for gas phase only. Use the Result Plot option to plot compressibility factor versus pressure and temperature, compressibility factor versus pressure and equation of state type, or compressibility factor versus temperature and equation of state type. Tool Input- fluidtype : Fluid Type
- SGu : User Defined Gas Specific Gravity
- ωu : User Defined Acentric Factor
- Pcu : User Defined Critical Pressure
- Tcu : User Defined Critical Temperature
- eostype : Equation Of State
- Zu : User Defined Compressibility Factor
- P : Fluid Pressure
- T : Fluid Temperature
Tool Output- ρ : Fluid Density
- ω : Accentric Factor
- Pc : Critical Point Pressure
- Pr : Reduced Pressure
- SG : Gas Specific Gravity Relative To Air
- Tc : Critical Point Temperature
- Tr : Reduced Temperature
- Vm : Molar Volume
- Z : Compressibility Factor
- cvg : Convergence Check
- mw : Fluid Molar Mass
|
CALCULATOR : Pipe Inside Diameter And Cross Section Area [FREE] ±
Calculate pipe inside diameter and inside cross section area from pipe diameter and wall thickness. Use the Result Table option to display a table of the inside diameter and cross section area versus either outside diameter or wall thickness. Tool Input- schdtype : Schedule Type
- diamtype : Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
- wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
Tool Output- AX : Pipe Inside Cross Section Area
- ID : Nominal Inside Diameter
- OD : Nominal Outside Diameter
- OD/tn : Diameter Over Wall Thickness Ratio
- tn : Nominal Wall Thickness
|
CALCULATOR : Liquid Density [FREE] ±
Calculate single phase liquid density from specific gravity, degrees Baume, degrees Twaddell, or degrees API. For liquids lighter than or equal to water the density can be defined as degrees API, or degrees Baume (Be-). For liquids heavier than water the density can be defined by degrees Baume (Be+), or degrees Twaddell. Tool Input- sgtype : Density Type
- SGu : User Defined Specific Gravity
- Be+u : User Defined Degrees Baume SG > 1
- Be-u : User Defined Degrees Baume SG <= 1
- Twu : User Defined Degrees Twaddell SG > 1
- APIu : User Defined Degrees API SG <= 1
- ρu : User Defined Liquid Density
Tool Output- ρ : Fluid Density
- API : Degrees API SG ≤ 1
- Be+ : Degrees Baume SG > 1
- Be- : Degrees Baume SG ≤ 1
- SG : Specific Gravity
- Tw : Degrees Twaddell SG > 1
|