ASME B31.3 Process Piping Basic Allowable Stress

Calculate ASME B31.3 process piping allowable stress (S), yield stress (SYT) and tensile stress (SUT) from temperature for low pressure piping (ASME B31.3 Table A-1) and high pressure piping (ASME B31.3 Table K-1).

Stress values are interpolated from the US data tables (US units govern). For temperatures below the data range, the stress value is constant (fracture toughness should also be considered for low temperature operation). For temperatures above the data range the stress values can either be constant value from the end point, constant slope from the end point, or zero from the end point. Engineering judgement is required to use extrapolated values above the data range.

Use the Data Plot option to plot the allowable stress versus temperature for the selected material. Use the Data Table option to display the data table in the popup window (Table A-1 or K-1). Use the Result Table option to display a table of allowable stress versus material type. Refer to the help pages for notes on the data tables. Change units on the setup page. Use the workbook ASME B31.3 data tables to look up allowable stress data.

Note : The choice of high pressure versus low pressure service is at the discretion of the owner (section FK300). The ASME B16.5 Class 2500 pressure temperature rating for the material group is often used as a criteria.

Reference : ANSI/ASME B31.3 : Process Piping (2018)

Change Module :

ASME B31.3 Process Piping Allowable Bolt Load And Bolt Stress Calculation Module
ASME B31.3 Process Piping Bend Calculation Module
ASME B31.3 Process Piping Blank Flange Calculation Module
ASME B31.3 Process Piping Branch Reinforcement Calculation Module
ASME B31.3 Process Piping Design Factor Calculation Module
ASME B31.3 Process Piping Design Pressure Calculation Module
ASME B31.3 Process Piping Elastic Modulus Calculation Module
ASME B31.3 Process Piping Fluid Velocity And Flow Rate Calculation Module
ASME B31.3 Process Piping Fluid Volume And Mass Calculation Module
ASME B31.3 Process Piping Hoop Stress Calculation Module
ASME B31.3 Process Piping Hydrotest Pressure Calculation Module
ASME B31.3 Process Piping Line Pipe Schedule Calculation Module
ASME B31.3 Process Piping Mass And Weight Calculation Module
ASME B31.3 Process Piping Minimum Temperature For Impact Testing Calculation Module
ASME B31.3 Process Piping Plastic Component Calculation Module
ASME B31.3 Process Piping Stress Factor And Flexibility Calculation Module
ASME B31.3 Process Piping Thermal Expansion Calculation Module
ASME B31.3 Process Piping Wall Thickness Calculation Module
All

Related Modules :

ASME B31.3 Process Piping Allowable Stress Data Module
More Allowable Stress Modules

[FREE] tools are free in basic mode with no login (no plots, tables, goal seek etc). Login or Open a free account to use the tools in plus mode (with plots, tables, goal seek etc).
[PLUS] tools are free in basic CHECK mode with Login or Open a free account (CHECK values no plots, tables, goal seek etc). Buy a Subscription to use the tools in plus mode (with plots, tables, goal seek etc).
Try plus mode using the Plus Mode Demo tools with no login. Help Using The Pipeng Toolbox (opens in the popup workbook)

Links : ±

CALCULATOR : ASME B31.3 Metal Pipe Diameter And Wall Thickness Schedule [FREE] ±

Calculate ASME B31.3 metal pipe diameter, minimum wall thickness and pressure design thickness from pipe schedule or user defined diameter and wall thickness (ASME B31.3 section 304.1).

Select the pipe schedule (NPS or ISO), pipe diameter and wall thickness, or use the user defined option. Use the Result Table option to display the pipe schedule with nominal wall thickness, minimum wall thickness and pressure design wall thickness for the selected diameter.

Tool Input

schdtype : Schedule Type
diamtype : Diameter Type
- ODu : User Defined Outside Diameter
- IDu : User Defined Inside Diameter
wtntype : Wall Thickness Type
- tnu : User Defined Wall Thickness
ttoltype : Wall Thickness Fabrication Tolerance Type
- txu : User Defined Negative Wall Thickness Fraction
- tfu : User Defined Negative Wall Thickness Allowance
c : Wall Thickness Corrosion Allowance

Tool Output

ID : Nominal Inside Diameter
OD : Nominal Outside Diameter
OD/tn : Diameter Over Wall Thickness Ratio
tf : Wall Thickness Fabrication Allowance
tm : Minimum Wall Thickness
tn : Nominal Wall Thickness
tp : Pressure Design Wall Thickness
tx : Wall Thickness Fabrication Fraction

CALCULATOR : ASME B31.3 Table A-1 Low Pressure Metal Pipe Yield Stress Tensile Stress And Basic Allowable Stress Schedule [FREE] ±

Calculate low pressure metal pipe SMYS (Specified Minimum Yield Stress), SMTS (Specified Minimum Tensile Stress) and basic allowable stress schedule (ASME B31.3 table A-1).

Use the Result Table option to display the stress values for the selected stress schedule (click the Result Table button, and then click the make table button).

Tool Input

syutype : Stress Schedule Type
mattype : Material Type
- SMTSu : User Defined Specified Minimum Tensile Stress
- SMYSu : User Defined Specified Minimum Yield Stress
- Su : User Defined Basic Allowable Stress

Tool Output

S : Basic Allowable Stress
S/SMTS : Basic Allowable Stress Over SMTS Ratio
S/SMYS : Basic Allowable Stress Over SMYS Ratio
SMTS : Specified Minimum Tensile Stress
SMTS/SMYS : SMTS Over SMYS Ratio
SMYS : Specified Minimum Yield Stress
SMYS/SMTS : SMYS Over SMTS Ratio

CALCULATOR : ASME B31.3 Table K-1 High Pressure Metal Pipe Yield Stress Tensile Stress And Allowable Stress Schedule [FREE] ±

Calculate high pressure metal pipe SMYS (Specified Minimum Yield Stress), SMTS (Specified Minimum Tensile Stress) and allowable stress schedule (ASME B31.3 table K-1).

Use the Result Table option to display the stress values for the selected stress schedule (click the Result Table button, and then click the make table button).

Tool Input

syutype : Stress Schedule Type
mattype : Material Type
- SMTSu : User Defined Specified Minimum Tensile Stress
- SMYSu : User Defined Specified Minimum Yield Stress
- Su : User Defined Allowable Stress

Tool Output

S : Basic Allowable Stress
S/SMTS : Basic Allowable Stress Over SMTS Ratio
S/SMYS : Basic Allowable Stress Over SMYS Ratio
SMTS : Specified Minimum Tensile Stress
SMTS/SMYS : SMTS Over SMYS Ratio
SMYS : Specified Minimum Yield Stress
SMYS/SMTS : SMYS Over SMTS Ratio

CALCULATOR : ASME B31.3 Section 323.2 Minimum Temperature Without Impact Testing For Carbon Steel Materials From Letter Designation [FREE] ±

Calculate the minimum design temperature without impact testing for carbon steel pipes and tubes with a minimum temperature letter designation (ASME B31.3 section 323.2). The values are interpolated from table 323.2.2A. The temperature values from table 323.2.2A vary slightly from the values in figure 323.2.2A. The curves A, B, C and D correspond to the minimum temperature designation from Table A-1.

The stress ratio reduction is taken from figure 323.2.2B. The stress ratio is the maximum of

The hoop stress over the basic allowable stress using the pressure containment wall thickness (nominal wall thickness minus fabrication allowance and corrosion allowance)
The operating pressure over the pressure rating (for pressure rated components)
The combined stress over the basic allowable stress using the nominal wall thickness.

Tool Input

tmintype : ASME B31.3 Table 323.2.2A Curve
- Tminu : User Defined Minimum Temperature Before Stress Ratio Reduction
sostype : Stress Ratio Reduction Type
Tn : Nominal Wall Thickness
S/Sa : Stress Over Allowable Stress Ratio

Tool Output

ΔT : Reduction In Minimum Temperature From Stress Ratio
Tmin : Minimum Temperature Before Stress Ratio Reduction
Tmin* : Minimum Temperature With Stress Ratio Reduction

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Cast Iron [PLUS] ±

Calculate allowable stress from temperature for iron casting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Carbon Steel Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for carbon steel pipe and tube (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (carbon steel). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Carbon Steel Pipe (Structural Grade) [PLUS] ±

Calculate allowable stress from temperature for carbon steel structural grade pipe (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (carbon steel). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Carbon Steel Plate Bar Shape Sheet [PLUS] ±

Calculate allowable stress from temperature for carbon steel plate bar shape and sheet (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (carbon steel). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Carbon Steel Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for carbon steel forging and fitting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (carbon steel). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Carbon Steel Casting [PLUS] ±

Calculate allowable stress from temperature for carbon steel casting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (carbon steel). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Carbon Steel Plate Bar Shape Sheet (Structural Grade) [PLUS] ±

Calculate allowable stress from temperature for carbon steel structural grade plate bar shape and sheet (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (carbon steel). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Alloy Steel Pipe [PLUS] ±

Calculate allowable stress from temperature for low and medium alloy steel pipe (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Alloy Steel Plate [PLUS] ±

Calculate allowable stress from temperature for low and medium alloy steel plate (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Alloy Steel Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for low and medium alloy steel forging and fitting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Alloy Steel Casting [PLUS] ±

Calculate allowable stress from temperature for low and medium alloy steel casting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Stainless Steel Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for stainless steel pipe and tube (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Stainless Steel Plate And Sheet [PLUS] ±

Calculate allowable stress from temperature for stainless steel plate and sheet (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Stainless Steel Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for stainless steel forging and fitting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Stainless Steel Bar [PLUS] ±

Calculate allowable stress from temperature for stainless steel bar (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Stainless Steel Casting [PLUS] ±

Calculate allowable stress from temperature for stainless steel casting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Copper Alloy Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for copper alloy pipe and tube (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Copper Alloy Plate And Sheet [PLUS] ±

Calculate allowable stress from temperature for copper alloy plate and sheet (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Copper Alloy Forging [PLUS] ±

Calculate allowable stress from temperature for copper alloy forging (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Copper Alloy Casting [PLUS] ±

Calculate allowable stress from temperature for copper alloy casting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Copper Alloy Rod [PLUS] ±

Calculate allowable stress from temperature for copper alloy rod (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Nickel Alloy Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for nickel alloy pipe and tube (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Nickel Alloy Plate And Sheet [PLUS] ±

Calculate allowable stress from temperature for nickel alloy plate and sheet (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Nickel Alloy Forging [PLUS] ±

Calculate allowable stress from temperature for nickel alloy forging (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Nickel Alloy Rod And Bar [PLUS] ±

Calculate allowable stress from temperature for nickel alloy rod and bar (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Nickel Alloy Casting [PLUS] ±

Calculate allowable stress from temperature for nickel alloy casting (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Titanium [PLUS] ±

Calculate allowable stress from temperature for titanium (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Zirconium [PLUS] ±

Calculate allowable stress from temperature for zirconium (ASME B31.3 Table A-1). The allowable stress values (S) are interpolated from table A-1 (low pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Aluminium Alloy Seamless Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for aluminium alloy seamless pipe and tube (ASME B31.3 Table A-1).

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Aluminium Alloy Structural Grade Pipe [PLUS] ±

Calculate allowable stress from temperature for aluminium alloy structural grade pipe (ASME B31.3 Table A-1).

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Aluminium Alloy Plate And Sheet [PLUS] ±

Calculate allowable stress from temperature for aluminium alloy plate and sheet (ASME B31.3 Table A-1).

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Aluminium Alloy Forging [PLUS] ±

Calculate allowable stress from temperature for aluminium alloy forging (ASME B31.3 Table A-1).

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Aluminium Alloy Casting [PLUS] ±

Calculate allowable stress from temperature for aluminium alloy casting (ASME B31.3 Table A-1).

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table A-1 Basic Allowable Stress From Temperature Aluminium Alloy Welded Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for aluminium alloy welded pipe and tube (ASME B31.3 Table A-1).

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
efactype : Quality Factor Type
- Eu : User Defined Quality Factor
wfactype : Weld Factor Type
- Wu : User Defined Weld Factor
- Tcr : User Defined Creep Temperature
Td : Design Temperature

Tool Output

E : Quality Factor
S : Basic Allowable Stress
SEW : Design Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Td [C] : Design Temperature
Tdata : Temperature Data
W : Weld Factor

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Carbon Steel Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for carbon steel pipe and tube (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Carbon Steel Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for carbon steel forging and fitting (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Alloy Steel Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for alloy steel pipe and tube (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Alloy Steel Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for alloy steel forging and fitting (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Stainless Steel Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for stainless steel pipe and tube (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Stainless Steel Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for stainless steel forging and fitting (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Nickel Alloy Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for nickel alloy pipe and tube (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Nickel Alloy Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for nickel alloy forging and fitting (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Nickel Alloy Rod And Bar [PLUS] ±

Calculate allowable stress from temperature for nickel alloy rod and bar (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Titanium Alloy Pipe And Tube [PLUS] ±

Calculate allowable stress from temperature for titanium alloy pipe and tube (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data

CALCULATOR : ASME B31.3 Table K-1 Allowable Stress From Temperature Titanium Alloy Forging And Fitting [PLUS] ±

Calculate allowable stress from temperature for titanium alloy forging and fitting (ASME B31.3 Table K-1). The allowable stress values (S) are interpolated from table K-1 (high pressure piping). Use the Result Table option to display a table of allowable stress versus material type at the design temperature.

Tool Input

datatype : Material Type And Grade
OOR : If Temperature Above Data Range
T : Design Temperature

Tool Output

S : Allowable Stress
SMTS : SMTS At 100 F
SMYS : SMYS At 100 F
SUT : Tensile Stress At Design Temperature
SYT : Yield Stress At Design Temperature
Sdata : Stress Data
So : Basic Allowable Stress At 100 F
Tdata : Temperature Data